 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| w wm8196 (8 + 8) bit output 16-bit cis/ccd afe/digitiser wolfson microelectronics plc to receive regular email updates, sign up at http://www.wolfsonmicro.com/enews/ production data, march 2007, rev 4.3 copyright ? 2007 wolfson microelectronics plc description the wm8196 is a 16-bit analogue front end/digitiser ic which processes and digitises the analogue output signals from ccd sensors or contact image sensors (cis) at pixel sample rates of up to 12msps. the device includes three analogue signal processing channels each of which contains reset level clamping, correlated double sampling and programmable gain and offset adjust functions. three multiplexers allow single channel processing. the output from each of these channels is time multiplexed into a single high-speed 16-bit analogue to digital converter. the digital output data is available in 8 or 4-bit wide multiplexed format. an internal 4-bit dac is supplied for internal reference level generation. this may be used during cds to reference cis signals or during reset level clamping to clamp ccd signals. an external reference level may also be supplied. adc references are generated internally, ensuring optimum performance from the device. using an analogue supply voltage of 5v and a digital interface supply of either 5v or 3.3v, the wm8196 typically only consumes 300mw when operating from a single 5v supply. features ? 16-bit adc ? 12msps conversion rate ? low power ? 320mw typical ? 5v single supply or 5v/3.3v dual supply operation ? single or 3 channel operation ? correlated double sampling ? programmable gain (8-bit resolution) ? programmable offset adjust (8-bit resolution) ? programmable clamp voltage ? 8 or 4-bit wide multiplexed data output formats ? internally generated voltage references ? 28-lead ssop package ? serial control interface applications ? flatbed and sheetfeed scanners ? usb compatible scanners ? multi-function peripherals ? high-performance ccd sensor interface block diagram rinp data i/o port sen vsmp mclk vrlc/vbias sdi sck dvdd2 timing control cl rlc/acyc rlc v s r s binp ginp vrx vrt oeb m u x vrb rlc rlc cds cds cds rlc dac 4 configurable serial control interface 16- bit adc agnd1 dgnd dvdd1 op[0] op[1] op[2] op[3] op[4] op[5] op[6] op[7]/sdo agnd2 m u x vref/bias m u x r g b m u x r g b + pga i/p signal polarity adjust 8 8 pga 8 8 offset dac pga 8 offset dac 8 + + + + + i/p signal polarity adjust i/p signal polarity adjust avdd w wm8196 offset dac
wm8196 production data w pd rev 4.3 march 2007 2 table of contents description .......................................................................................................1 features.............................................................................................................1 applications .....................................................................................................1 block diagram .................................................................................................1 table of contents .........................................................................................2 pin configuration...........................................................................................3 ordering information ..................................................................................3 pin description ................................................................................................4 absolute maximum ratings.........................................................................5 recommended operating conditions .....................................................5 thermal performance .................................................................................5 electrical characteristics ......................................................................6 input video sampling ............................................................................................. 8 output data timing ................................................................................................ 8 serial interface ................................................................................................... 10 internal power on reset circuit ..........................................................11 device description .......................................................................................13 introduction.......................................................................................................... 13 input sampling ....................................................................................................... 13 reset level clamping (rlc) ............................................................................... 13 cds/non-cds processing ................................................................................... 14 offset adjust and programmable gain....................................................... 15 adc input black level adjust .......................................................................... 16 overall signal flow summary ........................................................................ 16 calculating output for any given input .................................................... 16 output formats .................................................................................................... 17 control interface .............................................................................................. 18 timing requirements ........................................................................................... 19 programmable vsmp detect circuit ............................................................. 19 references............................................................................................................. 20 power supply ........................................................................................................ 20 power management ............................................................................................. 20 line-by-line operation ........................................................................................ 21 operating modes .................................................................................................. 22 operating mode timing diagrams ................................................................... 23 device configuration .................................................................................26 register map .......................................................................................................... 26 register map description ................................................................................. 27 applications information .........................................................................30 recommended external components........................................................... 30 recommended external component value ................................................ 30 package dimensions ....................................................................................31 important notice ..........................................................................................32 address:................................................................................................................... 32 wm8196 production data w pd rev 4.3 march 2007 3 ordering information device temperature range package moisture sensitivity levels peak soldering temperature wm8196scds 0 to 70 o c 28-lead ssop (pb free) msl1 260 o c wm8196scds/r 0 to 70 o c 28-lead ssop (pb free, tape and reel) msl1 260 o c note: reel quantity = 2,000 pin configuration sen op[1] op[0] sck sdi dvdd2 op[7]/sdo op[2] op[3] op[4] op[5] op[6] ginp agnd1 vrb vrt vrx vrlc/vbias binp avdd dgnd agnd2 dvdd1 oeb vsmp rlc/acyc mclk rinp 1 2 3 4 5 6 7 8 9 10 11 12 13 14 28 27 26 25 24 23 22 21 20 19 18 17 16 15 wm8196 production data w pd rev 4.3 march 2007 4 pin description pin name type description 1 rinp analogue input red channel input video. 2 agnd2 supply analogue ground (0v). 3 dvdd1 supply digital supply (5v) for logic and clock generator. this must be operated at the same potential as avdd. 4 oeb digital input output hi-z control, all digital outputs disabled when oeb = 1. 5 vsmp digital input video sample synchronisation pulse. 6 rlc/acyc digital input rlc (active high) selects reset level clamp on a pixel-by-pixel basis ? tie high if used on every pixel. acyc autocycles between r, g, b inputs. 7 mclk digital input master clock. this clock is applied at n times the input pixel rate (n = 2, 3, 6, 8 or any multiple of 2 thereafter depending on input sample mode). 8 dgnd supply digital ground (0v). 9 sen digital input enables the serial interface when high. 10 dvdd2 supply digital supply (5v/3.3v), all digital i/o pins. 11 sdi digital input serial data input. 12 sck digital input serial clock. digital multiplexed output data bus. adc output data (d15:d0) is available in two multiplexed formats as shown, under the control of register muxop [1:0] see ?output formats? description in device description section for further details. 8+8-bit 4+4+4+4-bit a b a b c d 13 op[0] digital output d8 d0 14 op[1] digital output d9 d1 15 op[2] digital output d10 d2 16 op[3] digital output d11 d3 17 op[4] digital output d12 d4 d12 d8 d4 d0 18 op[5] digital output d13 d5 d13 d9 d5 d1 19 op[6] digital output d14 d6 d14 d10 d6 d2 20 op[7]/sdo digital output d15 d7 d15 d11 d7 d3 alternatively, pin op[7]/sdo may be used to output register read-back data when oeb = 0 and sen has been pulsed high. see serial interface description in device description section for further details. 21 avdd supply analogue supply (5v). this must be operated at the same potential as dvdd1. 22 agnd1 supply analogue ground (0v). 23 vrb analogue output lower reference voltage. this pin must be connected to agnd via a decoupling capacitor. 24 vrt analogue output upper reference voltage. this pin must be connected to agnd via a decoupling capacitor. 25 vrx analogue output input return bias voltage. this pin must be connected to agnd via a decoupling capacitor. 26 vrlc/vbias analogue i/o selectable analogue output voltage for rlc or single-ended bias reference. this pin would typically be connected to agnd via a decoupling capacitor. vrlc can be externally driven if programmed hi-z. 27 binp analogue input blue channel input video. 28 ginp analogue input green channel input video. wm8196 production data w pd rev 4.3 march 2007 5 absolute maximum ratings absolute maximum ratings are stress ratings only. permanent damage to the device may be caused by continuously operating at or beyond these limits. device functional operating limits and guaranteed performance specifications are given under electrical characteristics at the test conditions specified. esd sensitive device. this device is manufactured on a cmos process. it is therefore generically susceptible to damage from excessive static voltages. proper esd precautions must be taken during handling and storage of this device. wolfson tests its package types according to ipc/jedec j-std-020b for moisture sensitivity to determine acceptable storage conditions prior to surface mount assembly. these levels are: msl1 = unlimited floor life at <30 c / 85% relative humidity. not normally stored in moisture barrier bag. msl2 = out of bag storage for 1 year at <30 c / 60% relative humidity. supplied in moisture barrier bag. msl3 = out of bag storage for 168 hours at <30 c / 60% relative humidity. supplied in moisture barrier bag. the moisture sensitivity level for each package type is specified in ordering information. condition min max analogue supply voltage: avdd gnd - 0.3v gnd + 7v digital supply voltages: dvdd1 ? 2 gnd - 0.3v gnd + 7v digital ground: dgnd gnd - 0.3v gnd + 0.3v analogue grounds: agnd1 ? 2 gnd - 0.3v gnd + 0.3v digital inputs, digital outputs and digital i/o pins gnd - 0.3v dvdd2 + 0.3v analogue inputs (rinp, ginp, binp) gnd - 0.3v avdd + 0.3v other pins gnd - 0.3v avdd + 0.3v operating temperature range: t a 0 c +70 c storage temperature prior to soldering 30 c max / 85% rh max storage temperature after soldering -65 c +150 c notes: 1. gnd denotes the voltage of any ground pin. 2. agnd1, agnd2 and dgnd pins are intended to be operated at the same potential. differential voltages between these pins will degrade performance. recommended operating conditions condition symbol min typ max units operating temperature range t a 0 70 c analogue supply voltage avdd 4.75 5.0 5.25 v digital core supply voltage dvdd1 4.75 5.0 5.25 v 5v i/o dvdd2 4.75 5.0 5.25 v digital i/o supply voltage 3.3v i/o dvdd2 2.97 3.3 3.63 v thermal performance parameter symbol test conditions min typ max unit performance thermal resistance ? junction to case r jc 23.9 c/w thermal resistance ? junction to ambient r ja t ambient = 25c 67.1 c/w notes: 1. figures given are for package mounted on 4-layer fr4 according to jesd51-5 and jesd51-7. wm8196 production data w pd rev 4.3 march 2007 6 electrical characteristics test conditions avdd = dvdd1 = 5.0v, dvdd2 = 3.3v, agnd = dgnd = 0v, t a = 25 c, mclk = 24mhz unless otherwise stated. parameter symbol test conditions min typ max unit overall system specification (including 16-bit adc, pga, offset and cds functions) conversion rate 12 msps full-scale input voltage range (see note 1) 0.4 4.08 vp-p vp-p input signal limits (see note 2) v in 0 avdd v full-scale transition error gain = 0db; pga[7:0] = 4b(hex) 20 mv zero-scale transition error gain = 0db; pga[7:0] = 4b(hex) 20 mv differential non-linearity dnl 1.25 lsb integral non-linearity inl 25 lsb channel to channel gain matching 1 % total output noise min gain max gain 4.5 14 lsb rms lsb rms references upper reference voltage vrt 2.85 v lower reference voltage vrb 1.35 v input return bias voltage vrx 1.4 1.65 1.6 v diff. reference voltage (vrt-vrb) v rtb 1.5 v output resistance vrt, vrb, vrx 1 ? vrlc/reset-level clamp (rlc) rlc switching impedance 50 ? vrlc short-circuit current 2 ma vrlc output resistance 2 ? vrlc hi-z leakage current vrlc = 0 to avdd 1 a rlcdac resolution 4 bits rlcdac step size, rlcdac = 0 v rlcstep avdd=5v 0.25 v/step rlcdac step size, rlcdac = 1 v rlcstep 0.17 v/step rlcdac output voltage at code 0(hex), rlcdacrng = 0 v rlcbot avdd=5v 0.39 v rlcdac output voltage at code 0(hex), rlcdacrng = 1 v rlcbot 0.26 v rlcdac output voltage at code f(hex) rlcdacrng, = 0 v rlctop avdd=5v 4.16 v rlcdac output voltage at code f(hex), rlcdacrng = 1 v rlctop 2.81 v vrlc deviation -50 +50 mv offset dac, monotonicity guaranteed resolution 8 bits differential non-linearity dnl 0.1 0.5 lsb integral non-linearity inl 0.25 1 lsb step size 2.04 mv/step output voltage code 00(hex) code ff(hex) -260 +260 mv mv notes: 1. full-scale input voltage denotes the maximum amplitude of the input signal at the specified gain. 2. input signal limits are the limits within which the full-scale input voltage signal must lie. wm8196 production data w pd rev 4.3 march 2007 7 test conditions avdd = dvdd1 = 5.0v, dvdd2 = 3.3v, agnd = dgnd = 0v, t a = 25 c, mclk = 24mhz unless otherwise stated. parameter symbol test conditions min typ max unit programmable gain amplifier resolution 8 bits gain ] 0 : 7 [ pga 283 208 ? v/v max gain, each channel g max 7.4 v/v min gain, each channel g min 0.74 v/v gain error, each channel 1 % analogue to digital converter resolution 16 bits speed 12 msps full-scale input range (2*(vrt-vrb)) 3 v digital specifications digital inputs high level input voltage v ih 0.8 ? dvdd2 v low level input voltage v il 0.2 ? dvdd2 v high level input current i ih 1 a low level input current i il 1 a input capacitance c i 5 pf digital outputs high level output voltage v oh i oh = 1ma dvdd2 - 0.5 v low level output voltage v ol i ol = 1ma 0.5 v high impedance output current i oz 1 a digital io pins applied high level input voltage v ih 0.8 ? dvdd2 v applied low level input voltage v il 0.2 ? dvdd2 v high level output voltage v oh i oh = 1ma dvdd2 - 0.5 v low level output voltage v ol i ol = 1ma 0.5 v low level input current i il 1 a high level input current i ih 1 a input capacitance c i 5 pf high impedance output current i oz 1 a supply currents total supply current ? active (three channel mode) mclk = 24mhz 60 ma total supply current ? active (single channel mode) linebyline = 1 mclk = 24mhz 45 ma total analogue supply current ? active (three channel mode) i avdd mclk = 24mhz 56 ma total analogue supply current ? active (one channel mode) i avdd linebyline = 1 mclk = 24mhz 41 ma digital core supply current, dvdd1 ? active (note1) mclk = 24mhz 3 ma digital i/o supply current, dvdd2 ? active (note1) mclk = 24mhz 1 ma supply current ? full power down mode 300 a wm8196 production data w pd rev 4.3 march 2007 8 input video sampling mclk vsmp input video t per t vsmpsu t vsmph t vsu t vh t rsu t rh t mclkl t mclkh figure 1 input video timing note: 1. see page 14 (programmable vsmp detect circuit) for video sampling description. test conditions avdd = dvdd1 = 5.0v, dvdd2 = 3.3v, agnd = dgnd = 0v, t a = 25 c, mclk = 24mhz unless otherwise stated. parameter symbol test conditions min typ max units mclk period t per 41.6 ns mclk high period t mclkh 18.8 ns mclk low period t mclkl 18.8 ns vsmp set-up time t vsmpsu 6 ns vsmp hold time t vsmph 3 ns video level set-up time t vsu 10 ns video level hold time t vh 3 ns reset level set-up time t rsu 10 ns reset level hold time t rh 3 ns notes: 1. t vsu and t rsu denote the set-up time required after the input video signal has settled. 2. parameters are measured at 50% of the rising/falling edge. output data timing mclk op[7:0] t pd figure 2 output data timing wm8196 production data w pd rev 4.3 march 2007 9 oeb op[7:0] t pze hi-z t pez hi-z figure 3 output data enable timing test conditions avdd = dvdd1 = 5.0v, dvdd2 = 3.3v, agnd = dgnd = 0v, t a = 25 c, mclk = 24mhz unless otherwise stated. parameter symbol test conditions min typ max units output propagation delay t pd i oh = 1ma, i ol = 1ma 40 ns output enable time t pze 20 ns output disable time t pez 15 ns mclk rlc/acyc pga/offset mux output t acycsu t acych t acycsu t acych figure 4 auto cycle timing test conditions avdd = dvdd1 = 5.0v, dvdd2 = 3.3v, agnd = dgnd = 0v, t a = 25 c, mclk = 24mhz unless otherwise stated. parameter symbol test conditions min typ max units auto cycle set-up time t acycsu 6 ns auto cycle hold time t acych 3 ns wm8196 production data w pd rev 4.3 march 2007 10 serial interface sck sdi sen sdo t sper t sckl t sckh t ssu t sh t sce t sew t sec t serd t scrd msb lsb t scrdz adc data adc data register data figure 5 serial interface timing test conditions avdd = dvdd1 = 5.0v, dvdd2 = 3.3v, agnd = dgnd = 0v, t a = 25 c, mclk = 24mhz unless otherwise stated. parameter symbol test conditions min typ max units sck period t sper 41.6 ns sck high t sckh 18.8 ns sck low t sckl 18.8 ns sdi set-up time t ssu 6 ns sdi hold time t sh 6 ns sck to sen set-up time t sce 12 ns sen to sck set-up time t sec 12 ns sen pulse width t sew 25 ns sen low to sdo = register data t serd 30 ns sck low to sdo = register data t scrd 30 ns sck low to sdo = adc data t scrdz 30 ns note: 1. parameters are measured at 50% of the rising/falling edge wm8196 production data w pd rev 4.3 march 2007 11 internal power on reset circuit figure 6 internal power on reset circuit schematic the wm8196 includes an internal power-on-reset circuit, as shown in figure 6, which is used to reset the digital logic into a default state after power up. the por circuit is powered from avdd and monitors dvdd1. it asserts porb low if avdd or dvdd1 is below a minimum threshold. the power supplies can be brought up in any order but is important that either avdd is brought up and is stable before dvdd comes up or vice versa as shown in figure 7 and figure 8. figure 7 typical power up sequence where avdd is powered before dvdd1 figure 7 shows a typical power-up sequence where avdd is powered up first. when avdd rises above the minimum threshold, vpora, there is enough voltage for the circuit to guarantee porb is asserted low and the chip is held in reset. in this condition, all writes to the control interface are ignored. now avdd is at full supply level. next dvdd1 rises to vpord_on and porb is released high and all registers are in their default state and writes to the control interface may take place. on power down, where avdd falls first, porb is asserted low whenever avdd drops below the minimum threshold vpora_off. wm8196 production data w pd rev 4.3 march 2007 12 figure 8 typical power up sequence where dvdd1 is powered before avdd figure 8 shows a typical power-up sequence where dvdd1 is powered up first. it is assumed that dvdd1 is already up to specified operating voltage. when avdd goes above the minimum threshold, vpora, there is enough voltage for the circuit to guarantee porb is asserted low and the chip is held in reset. in this condition, all writes to the control interface are ignored. when avdd rises to vpora_on, porb is released high and all registers are in their default state and writes to the control interface may take place. on power down, where dvdd1 falls first, porb is asserted low whenever dvdd1 drops below the minimum threshold vpord_off. symbol typ unit v pora 0.6 v v pora_on 1.2 v v pora_off 0.6 v v pord_on 0.7 v v pord_off 0.6 v table 1 typical por operation (typical values, not tested) note : it is recommended that every time power is cycled to the wm 8196 a software reset is written to the software register to ensure that the contents of the control registers are at their default values before carrying out any other register writes. wm8196 production data w pd rev 4.3 march 2007 13 device description introduction a block diagram of the device showing the signal path is presented on page 1. the wm8196 samples up to three inputs (rinp, ginp and binp) simultaneously. the device then processes the sampled video signal with respect to the video reset level or an internally/externally generated reference level using either one or three processing channels. each processing channel consists of an input sampling block with optional reset level clamping (rlc) and correlated double sampling (cds), an 8-bit programmable offset dac and an 8-bit programmable gain amplifier (pga). the adc then converts each resulting analogue signal to a 16-bit digital word. the digital output from the adc is presented on an 8-bit wide bi-directional bus, with optional 8 or 4-bit multiplexed formats. on-chip control registers determine the configuration of the device, including the offsets and gains applied to each channel. these registers are programmable via a serial interface. input sampling the wm8196 can sample and process one to three inputs through one or three processing channels as follows: colour pixel-by-pixel: the three inputs (rinp, ginp and binp) are simultaneously sampled for each pixel and a separate channel processes each input. the signals are then multiplexed into the adc, which converts all three inputs within the pixel period. monochrome: a single chosen input (rinp, ginp, or binp) is sampled, processed by the corresponding channel, and converted by the adc. the choice of input and channel can be changed via the control interface, e.g. on a line-by-line basis if required. colour line-by-line: a single chosen input (rinp, ginp, or binp) is sampled and multiplexed into the red channel for processing before being converted by the adc. the input selected can be switched in turn (rinp ginp binp rinp?) together with the pga and offset dac control registers by pulsing the rlc/acyc pin. this is known as auto-cycling. alternatively, other sampling sequences can be generated via the control registers. this mode causes the blue and green channels to be powered down. refer to the line-by-line operation section for more details. reset level clamping (rlc) to ensure that the signal applied to the wm8196 lies within its input range (0v to avdd) the ccd output signal is usually level shifted by coupling through a capacitor, c in. the rlc circuit clamps the wm8196 side of this capacitor to a suitable voltage during the ccd reset period. a typical input configuration is shown in figure 9. an internal clamp pulse, cl, is generated from mclk and vsmp by the timing control block. when cl is active the voltage on the wm8196 side of c in , at rinp, is forced to the vrlc/vbias voltage (v vrlc ) by closing of switch 1. when the cl pulse turns off switch 1 opens, the voltage at rinp initially remains at v vrlc but any subsequent variation in sensor voltage (from reset to video level) will couple through c in to rinp. rlc is compatible with both cds and non-cds operating modes, as selected by switch 2. refer to the cds/non-cds processing section. wm8196 production data w pd rev 4.3 march 2007 14 timing control s/h 4-bit rlc dac cl + + - to offset dac rlc cds from control interface s/h v s r s from control interface mclk vsmp rlc/acyc input sampling block for red channel cds c in rinp vrlc/ vbias 2 1 external vrlc vrlcext figure 9 reset level clamping and cds circuitry if auto-cycling is not required, rlc can be selected by pin rlc/acyc. figure 10 illustrates control of rlc for a typical ccd waveform, with cl applied during the reset period. the input signal applied to the rlc/acyc pin is sampled on the positive edge of mclk that occurs during each vsmp pulse. the sampled level, high (or low) controls the presence (or absence) of the internal cl pulse on the next reset level. the position of cl can be adjusted by using control bits cdsref[1:0] (figure 11). if auto-cycling is required, pin rlc/acyc is no longer available for this function and control bit rlcint determines whether clamping is applied. figure 10 relationship of rlc pin, mclk and vsmp to internal clamp pulse, cl the vrlc/vbias pin can be driven internally by a 4-bit dac (rlcdac) by writing to control bits rlcv[3:0]. the rlcdac range and step size may be increased by writing to control bit rlcdacrng. alternatively, the vrlc/vbias pin can be driven externally by writing to control bit vrlcext to disable the rlcdac and then applying a d.c. voltage to the pin. cds/non-cds processing for ccd type input signals, the signal may be processed using cds, which will remove pixel-by-pixel common mode noise. for cds operation, the video level is processed with respect to the video reset level, regardless of whether rlc has been performed. to sample using cds, control bit cds must be set to 1 (default), this sets switch 2 into the position shown in figure 9 and causes the signal reference to come from the video reset level. the time at which the reset level is sampled, by clock r s /cl, is adjustable by programming control bits cdsref[1:0], as shown in figure 11. mclk vsmp acyc/rlc or rlcint cl (cdsref = 01) input video 1x x 0x x 0 rgb rgb no rlc on this pixel rlc on this pixel programmable delay rgb wm8196 production data w pd rev 4.3 march 2007 15 mclk vsmp vs r s /cl (cdsref = 00) r s /cl (cdsref = 01) r s /cl (cdsref = 10) r s /cl (cdsref = 11) figure 11 reset sample and clamp timing for cis type sensor signals, non-cds processing is used. in this case, the video level is processed with respect to the voltage on pin vrlc/vbias, generated internally or externally as described above. the vrlc/vbias pin is sampled by r s at the same time as v s samples the video level in this mode; non-cds processing is achieved by setting switch 2 in the lower position, cds = 0. offset adjust and programmable gain the output from the cds block is a differential signal, which is added to the output of an 8-bit offset dac to compensate for offsets and then amplified by an 8-bit pga. the gain and offset for each channel are independently programmable by writing to control bits dac[7:0] and pga[7:0]. the gain characteristic of the wm8196 pga is shown in figure 12. figure 13 shows the maximum device input voltage that can be gained up to match the adc full-scale input range (3v). 0 1 2 3 4 5 6 7 8 0 64 128 192 256 gain register value (pga[7:0]) pga gain (v/v) 0 0.5 1 1.5 2 2.5 3 3.5 4 4.5 0 64 128 192 256 gain register value (pga[7:0]) peak input voltage to match adc full - scale input range figure 12 pga gain characteristic figure 13 peak input voltage to match adc full-scale range in colour line-by-line mode the gain and offset coefficients for each colour can be multiplexed in order (red green blue red?) by pulsing the acyc/rlc pin, or controlled via the fme, acycnrlc and intm[1:0] bits. refer to the line-by-line operation section for more details. wm8196 production data w pd rev 4.3 march 2007 16 adc input black level adjust the output from the pga should be offset to match the full-scale range of the adc (3v). for negative-going input video signals, a black level (zero differential) output from the pga should be offset to the top of the adc range by setting register bits pgafs[1:0]=10. for positive going input signal the black level should be offset to the bottom of the adc range by setting pgafs[1:0]=11. bipolar input video is accommodated by setting pgafs[1:0]=00 or pgafs[1:0]=01 (zero differential input voltage gives mid-range adc output). overall signal flow summary figure 14 represents the processing of the video signal through the wm8196. v reset v vrlc v 3 cds = 1 cds = 0 rlcext=1 260mv*(dac[7:0]-127.5)/127.5 analog - x + + see parametrics for dac voltages. op[7:0] d 1 digital adc block pga block offset dac block input sampling block d 2 cds, rlcext,rlcv[3:0], dac[7:0], pga[7:0], pgafs[1:0] and invop are set by programming internal control registers. cds=1 for cds, 0 for non-cds v in is rinp or ginp or binp v reset is v in sampled during reset clamp vrlc is voltage applied to vrlc pin v in x (65535/v fs ) +0 if pgafs[1:0]=11 +65535 if pgafs[1:0]=10 +32768 if pgafs[1:0]=0x pga gain a = 208/(283-pga[7:0]) output invert block d2 = d1 if invop = 0 d2 = 65535-d1 if invop = 1 offset dac rlc dac + v 2 v 1 rlcext=0 figure 14 overall signal flow the input sampling block produces an effective input voltage v 1 . for cds, this is the difference between the input video level v in and the input reset level v reset . for non-cds this is the difference between the input video level v in and the voltage on the vrlc/vbias pin, v vrlc , optionally set via the rlc dac. the offset dac block then adds the amount of fine offset adjustment required to move the black level of the input signal towards 0v, producing v 2 . the pga block then amplifies the white level of the input signal to maximise the adc range, outputting voltage v 3 . the adc block then converts the analogue signal, v 3 , to a 16-bit unsigned digital output, d 1 . the digital output is then inverted, if required, through the output invert block to produce d 2. calculating output for any given input the following equations describe the processing of the video and reset level signals through the wm8196. the values if v 1 v 2 and v 3 are often calculated in reverse order during device setup. the pga value is written first to set the input voltage range, the offset dac is then adjusted to compensate for any black/reset level offsets and finally the rlc dac value is set to position the reset level correctly during operation. note: refer to wan0123 for detailed information on device calibration procedures. input sampling block: input sampling and referencing if cds = 1, (i.e. cds operation) the previously sampled reset level, v reset , is subtracted from the input video. v 1 = v in - v reset ................................................................... eqn. 1 if cds = 0, (non-cds operation) the simultaneously sampled voltage on pin vrlc is subtracted instead. v 1 = v in - v vrlc .................................................................... eqn. 2 if rlcext = 1, v vrlc is an externally applied voltage on pin vrlc/vbias. wm8196 production data w pd rev 4.3 march 2007 17 if rlcext = 0, v vrlc is the output from the internal rlc dac. v vrlc = (v rlcstep ? rlcv[3:0]) + v rlcbot ................................. eqn. 3 v rlcstep is the step size of the rlc dac and v rlcbot is the minimum output of the rlc dac. offset dac block: offset (black-level) adjust the resultant signal v 1 is added to the offset dac output. v 2 = v 1 + {260mv ? (dac[7:0]-127.5) } / 127.5 ..................... eqn. 4 pga node: gain adjust the signal is then multiplied by the pga gain, v 3 = v 2 ? 208/(283- pga[7:0]) .............................................. eqn. 5 adc block: analogue-digital conversion the analogue signal is then converted to a 16-bit unsigned number, with input range configured by pgafs[1:0]. d 1 [15:0] = int{ ( v 3 /v fs ) ? 65535} + 32767 pgafs[1:0] = 00 or 01 ...... eqn. 6 d 1 [15:0] = int{ ( v 3 /v fs ) ? 65535} pgafs[1:0] = 11 ............... eqn. 7 d 1 [15:0] = int{ ( v 3 /v fs ) ? 65535} + 65535 pgafs[1:0] = 10 ............... eqn. 8 where the adc full-scale range, v fs = 3v output invert block: polarity adjust the polarity of the digital output may be inverted by control bit invop. d 2 [15:0] = d 1 [15:0] (invop = 0) ...................... eqn. 9 d 2 [15:0] = 65535 ? d 1 [15:0] (invop = 1) ...................... eqn. 10 output formats the digital data output from the adc is available to the user in 8 or 4-bit wide multiplexed formats by setting control bit muxop[1:0]. latency of valid output data with respect to vsmp is programmable by writing to control bits del[1:0]. the latency for each mode is shown in the operating mode timing diagrams section. figure 15 shows the output data formats for modes 1 ? 2 and 4 ? 6. figure 16 shows the output data formats for mode 3. table 2 summarises the output data obtained for each format. mclk 4+4+4+4-bit output ab ab cd 8+8-bit output mclk 4+4+4+4-bit output ab 8+8-bit output ab c d ab figure 15 output data formats (modes 1 ? 2, 4 ? 6) figure 16 output data formats (mode 3) wm8196 production data w pd rev 4.3 march 2007 18 output format muxop[1:0] output pins output 8+8-bit multiplexed 00, 01, 10 op[7:0] a = d15, d14, d13, d12, d11, d10, d9, d8 b = d7, d6, d5, d4, d3, d2, d1,d0 4+4+4+4-bit (nibble) 11 op[7:4] a = d15, d14, d13, d12 b = d11, d10, d9, d8 c = d7, d6, d5, d4 d = d3, d2, d1, d0 table 2 details of output data shown in figure 15 and figure 16. control interface the internal control registers are programmable via the serial digital control interface. the register contents can be read back via the serial interface on pin op[7]/sdo. note: it is recommended that a software reset is carried out after the power-up sequence, before writing to any other register. this ensures that all registers are set to their default values (as shown in table 6). serial interface: register write figure 17 shows register writing in serial mode. three pins, sck, sdi and sen are used. a six-bit address (a5, 0, a3, a2, a1, a0) is clocked in through sdi, msb first, followed by an eight-bit data word (b7, b6, b5, b4, b3, b2, b1, b0), also msb first. each bit is latched on the rising edge of sck. when the data has been shifted into the device, a pulse is applied to sen to transfer the data to the appropriate internal register. note all valid registers have address bit a4 equal to 0 in write mode. sck sen sdi a5 0 a3a2a1a0b7b6b5b4b3b2b1b0 address data word figure 17 serial interface register write a software reset is carried out by writing to address ?000100? with any value of data, i.e. data word = xxxxxxxx. serial interface: register read-back figure 18 shows register read-back in serial mode. read-back is initiated by writing to the serial bus as described above but with address bit a4 set to 1, followed by an 8-bit dummy data word. writing address (a5, 1, a3, a2, a1, a0) will cause the contents (d7, d6, d5, d4, d3, d2, d1, d0) of corresponding register (a5, 0, a3, a2, a1, a0) to be output msb first on pin sdo (on the falling edge of sck). note that pin sdo is shared with an output pin, op[7], therefore oeb should always be held low when register read-back data is expected on this pin. the next word may be read in to sdi while the previous word is still being output on sdo. wm8196 production data w pd rev 4.3 march 2007 19 sck sen sdi a51a3a2a1a0xxxxxxxx address data word d7 d6 d5 d4 d3 d2 d1 d0 output data word sdo/ op[7] oeb figure 18 serial interface register read-back timing requirements to use this device a master clock (mclk) of up to 24mhz and a per-pixel synchronisation clock (vsmp) of up to 12mhz are required. these clo cks drive a timing control block, which pr oduces internal signals to control the sampling of the video signal. mclk to vsmp ratios and maximum sample rates for the various modes are shown in table 5. programmable vsmp detect circuit the vsmp input is used to determine the sampling point and frequency of the wm8196. under normal operation a pulse of 1 mclk period should be applied to vsmp at the desired sampling frequency (as shown in the operating mode timing diagrams) and the input sample will be taken on the first rising mclk edge after vsmp has gone low. however, in certain applications such a signal may not be readily available. the programmable vsmp detect circuit in the wm8196 allows the sampling point to be derived from any signal of the correct frequency, such as a ccd shift register clock, when applied to the vsmp pin. when enabled, by setting the vsmpdet control bit, the circuit detects either a rising or falling edge (determined by posnneg control bit) on the vsmp input pin and generates an internal vsmp pulse. this pulse can optionally be delayed by a number of mclk periods, specified by the vdel[2:0] bits. figure 19 shows the internal vsmp pulses that can be generated by this circuit for a typical clock input signal. the internal vsmp pulse is then applied to the timing control block in place of the normal vsmp pulse provided from the input pin. the sampling point then occurs on the first rising mclk edge after this internal vsmp pulse, as shown in the operating mode timing diagrams. wm8196 production data w pd rev 4.3 march 2007 20 mclk vsmp (vdel = 000) intvsmp posnneg = 1 (vdel = 001) intvsmp (vdel = 010) intvsmp (vdel = 011) intvsmp (vdel = 100) intvsmp (vdel = 101) intvsmp (vdel = 110) intvsmp (vdel = 111) intvsmp posnneg = 0 (vdel = 000) intvsmp (vdel = 001) intvsmp (vdel = 010) intvsmp (vdel = 011) intvsmp (vdel = 100) intvsmp (vdel = 101) intvsmp (vdel = 110) intvsmp (vdel = 111) intvsmp input pins v s v s v s v s v s v s v s v s v s v s v s v s v s v s v s v s v s v s v s v s v s v s v s v s v s v s v s v s v s v s v s v s v s v s v s v s v s v s v s v s v s v s v s v s v s v s v s v s figure 19 internal vsmp pulses generated by programmable vsmp detect circuit references the adc reference voltages are derived from an internal bandgap reference, and buffered to pins vrt and vrb, where they must be decoupled to ground. pin vrx is driven by a similar buffer, and also requires decoupling. the output buffer from the rlcdac also requires decoupling at pin vrlc/vbias power supply the wm8196 can run from a 5v single supply or from split 5v (core) and 3.3v (digital interface) supplies. power management power management for the device is performed via the control interface. the device can be powered on or off completely setting by the en bit and selpd bit low. alternatively, when control bit selpd is high, only blocks selected by further control bits (seldis[3:0]) are powered down. this allows the user to optimise power dissipation in certain modes, or to define an intermediate standby mode to allow a quicker recovery into a fully active state. in line-by-line operation, the green and blue channel pgas are automatically powered down. all the internal registers maintain their previously programmed value in power down modes and the control interface inputs remain active. table 3 summarises the power down control bit functions. en seldpd 0 0 device completely powers down. 1 0 device completely powers up. x 1 blocks with respective seldis[3:0] bit high are disabled. table 3 power down control wm8196 production data w pd rev 4.3 march 2007 21 line-by-line operation certain linear sensors (e.g. contact image sensors) give colour output on a line-by-line basis. i.e. a full line of red pixels followed by a line of green pixels followed by a line of blue pixels. in order to accommodate this type of signal the wm8196 can be set into monochrome mode, with the input channel switched by writing to control bits chan[1:0] between every line. alternatively, the wm8196 can be placed into colour line-by-line mode by setting the linebyline control bit. when this bit is set the green and blue processing channels are powered down and the device is forced internally to only operate in mono mode (because only one colour is sampled at a time) through the red channel. figure 20 shows the signal path when operating in colour line-by-line mode. rinp sen/stb v smp mclk v rlc/vbias sdi/dna sck/rnw rlc/acyc rlc binp ginp input mux offset mux rlc r g b r g b pga i/p signal polarity adjust 8 rlc dac + configurable serial/ parallel control interface op[7:0] + 16- bit adc data i/o port 8 offset dac pga mux timing control cl v s r s 4 cds rlc nreset figure 20 signal path when in line-by-line mode in this mode the input multiplexer and (optionally) the pga/offset register multiplexers can be auto- cycled by the application of pulses to the rlc/acyc input pin by setting the acycnrlc register bit. see figure 4 for detailed timing information. the multiplexers change on the first mclk rising edge after rlc/acyc is taken high. a write to the auto-cycle reset register causes these multiplexers to be reset; selecting the rinp pin and the red offset/gain registers. alternatively, all three multiplexers can be controlled via the serial interface by writing to register bits intm[1:0] to select the desired colour. it is also possible for the input multiplexer to be controlled separately from the pga and offset multiplexers. table 4 describes all the multiplexer selection modes that are possible. fme acycnrlc name description 0 0 internal, no force mux input mux, offset and gain registers determined by internal register bits intm1, intm0. 0 1 auto-cycling, no force mux input mux, offset and gain registers auto-cycled, rinp ginp binp rinp? on rlc/acyc pulse. 1 0 internal, force mux input mux selected from internal register bits fm1, fm0; offset and gain registers selected from internal register bits intm1, intm0. 1 1 auto-cycling, force mux input mux selected from internal register bits fm1, fm0; offset and gain registers auto-cycled, red green blue red? on rlc/acyc pulse. table 4 colour selection description in line-by-line mode wm8196 production data w pd rev 4.3 march 2007 22 operating modes table 5 summarises the most commonly used modes, the clock waveforms required and the register contents required for cds and non-cds operation. mode description cds available max sample rate sensor interface description timing require- ments register contents with cds register contents without cds 1 colour pixel-by-pixel yes 4msps the 3 input channels are sampled in parallel. the signal is then gain and offset adjusted before being multiplexed into a single data stream and converted by the adc, giving an output data rate of 12msps max. mclk max = 24mhz mclk: vsmp ratio is 6:1 setreg1: 03(hex) setreg1: 01(hex) 2 monochrome/ colour line-by-line yes 4msps as mode 1 except: only one input channel at a time is continuously sampled. mclk max = 24mhz mclk: vsmp ratio is 6:1 setreg1: 07(hex) setreg1: 05(hex) 3 fast monochrome/ colour line-by-line yes 8msps identical to mode 2 mclk max = 24mhz mclk: vsmp ratio is 3:1 identical to mode 2 plus setreg3: bits 5:4 must be set to 0(hex) identical to mode 2 4 maximum speed monochrome/ colour line-by-line no 12msps identical to mode 2 mclk max = 24mhz mclk: vsmp ratio is 2:1 cds not possible setreg1: 45(hex) 5 slow colour pixel-by-pixel yes 3msps identical to mode 1 mclk max = 24mhz mclk: vsmp ratio is 2n:1, n 4 identical to mode 1 identical to mode 1 6 slow monochrome/ colour line-by-line yes 3mps identical to mode 2 mclk max = 24mhz mclk: vsmp ratio is 2n:1, n 4 identical to mode 2 identical to mode 2 table 5 wm8196 operating modes notes: 1. in monochrome mode, setreg3 bits 7:6 determine which input is to be sampled. 2. for colour line-by-line, set control bit linebyline. for input selection, refer to table 4, colour selection description in line-by-line mode. wm8196 production data w pd rev 4.3 march 2007 23 operating mode timing diagrams the following diagrams show 8-bit multiplexed output data and mclk, vsmp and input video requirements for operation of the most commonly used modes as shown in table 5. the diagrams are identical for both cds and non-cds operation. outputs from rinp, ginp and binp are shown as r, g and b respectively. x denotes invalid data. mclk vsmp input video op[7:0] (del = 00) 16.5 mclk periods r a r b g a g b b a b b r a r b g a g b b a b b r a r b g a g b b a b b r a r b r a r b g a g b b a b b op[7:0] (del = 01) b a b b r a r b g a g b b a b b r a r b g a g b b a b b r a r b g a g b b a b b b a b b r a r b g a g b op[7:0] (del = 10) g a g b b a b b r a r b g a g b b a b b r a r b g a g b b a b b r a r b g a g b g a g b b a b b r a r b op[7:0] (del = 11) r a r b g a g b b a b b r a r b g a g b b a b b r a r b g b g a b a b b r a r b r a r b g a g b b a b b b a b b g a g b b a b b r a r b r a r b g a g b g a g b b a b b figure 21 mode 1 operation figure 22 mode 2 operation wm8196 production data w pd rev 4.3 march 2007 24 figure 23 mode 3 operation figure 24 mode 4 operation wm8196 production data w pd rev 4.3 march 2007 25 16.5 mclk periods mclk vsmp input video op[7:0] (del = 00) x x r a r b g a g b b a b b x x r a r b g a g b b a b b x x r a r b g a g b b a b b op[7:0] (del = 01) x x r a r b g a g b b a b b x x r a r b g a g b b a b b x x r a r b g a g b b a b b op[7:0] (del = 10) x x r a r b g a g b b a b b x x r a r b g a g b b a b b x x r a r b g a g b b a b b op[7:0] (del = 11) x x r a r b g a g b b a b b x x r a r b g a g b b a b b x x r a r b g a g b b a b b b a b b x x g a g b b a b b r a r b g a g b b a b b x x x x r a r b r a r b g a g b figure 25 mode 5 operation (mclk:vsmp ratio = 8:1) figure 26 mode 6 operation (mclk:vsmp ratio = 8:1) wm8196 production data w pd rev 4.3 march 2007 26 device configuration register map the following table describes the location of each control bit used to determine the operation of the wm8196. the register map is programmed by writing the required codes to the appropriate addresses via the serial interface. bit address wm8196 production data w pd rev 4.3 march 2007 27 register map description the following table describes the function of each of the control bits shown in table 6. register bit no bit name(s) default description 0 en 1 when selpd = 1 this bit has no effect. when selpd = 0 this bit controls the global power down: 0 = complete power down, 1 = fully active. 1 cds 1 select correlated double sampling mode: 0 = single ended mode, 1 = cds mode. 2 mono 0 mono/colour select: 0 = colour, 1 = monochrome operation. 3 selpd 0 selective power down: 0 = no individual control, 1 = individual blo cks can be disabled (controlled by seldis[3:0]). offsets pga output to optimise the adc range for different polarity sensor output signals. zero differential pga input signal gives: 5:4 pgafs[1:0] 00 00 = zero output (use for bipolar video) 01 = zero output 10 = full-scale positive output (use for negative going video) 11 = full-scale negative output (use for positive going video) 6 mode4 0 required when operating in mode4: 0 = other modes, 1 = mode4. setup register 1 7 reserved 0 must be set to zero determines the output data format. 1:0 muxop[1:0] 00 00 = 16-bit parallel 01 = 8-bit multiplexed (8+8 bits) 10 = 8-bit multiplexed mode (8+8 bits) 11 = 4-bit multiplexed mode (4+4+4+4 bits) 2 invop 0 digitally inverts the polarity of output data. 0 = negative going video gives negative going output, 1 = negative-going video gives positive going output data. 3 vrlcext 0 when set powers down the rlcdac, changing its output to hi-z, allowing vrlc/vbias to be externally driven. 5 rlcdacrng 1 sets the output range of the rlcdac. 0 = rlcdac ranges from 0 to avdd (approximately), 1 = rlcdac ranges from 0 to vrt (approximately). sets the output latency in adc clock periods. 1 adc clock period = 2 mclk periods except in mode 3 where 1 adc clock period = 3 mclk periods. setup register 2 7:6 del[1:0] 00 00 = minimum latency 01 = delay by one adc clock period 10 = delay by two adc clock periods 11 = delay by three adc clock periods 3:0 rlcv[3:0] 1111 controls rlcdac driving vrlc pin to define single ended signal reference voltage or reset level clamp voltage. see electrical characteristics section for ranges. cds mode reset timing adjust. 5:4 cdsref[1:0] 01 00 = advance 1 mclk period 01 = normal 10 = retard 1 mclk period 11 = retard 2 mclk periods monochrome mode channel select. setup register 3 7:6 chan[1:0] 00 00 = red channel select 01 = green channel select 10 = blue channel select 11 = reserved software reset any write to software reset causes all cells to be reset. it is recommended that a software reset be performed after a power-up before any other register writes. auto-cycle reset any write to auto-cycle reset causes the auto-cycle counter to reset to rinp. this function is only required when lin ebyline = 1. wm8196 production data w pd rev 4.3 march 2007 28 register bit no bit name(s) default description 0 linebyline 0 selects line by line operation 0 = normal operation, 1 = line by line operation. when line by line operation is selected mono is forced to 1 and chan[1:0] to 00 internally, ensuring that the correct internal timing signals are produced. green and blue pgas are also disabled to save power. 1 acycnrlc 0 when linebyline = 0 this bit has no effect. when linebyline = 1 this bit determines the function of the rlc/acyc input pin and the input multiplexer and offset/gain register controls. 0 = rlc/acyc pin enabled for reset level clamp. internal selection of input and gain/offset multiplexers, 1 = auto-cycling enabled by pulsing the rlc/acyc input pin. see table 4, colour selection description in line-by-line mode for colour selection mode details. when auto-cycling is enabled, the rlc/acyc pin cannot be used for reset level clamping. the rlcint bit may be used instead. 2 fme 0 when linebyline = 0 this bit has no effect. when linebyline = 1 this bit controls the input force mux mode: 0 = no force mux, 1 = force mux mode. forces the input mux to be selected by fm[1:0] separately from gain and offset multiplexers. see table 4 for details. 3 rlcint 0 when linebyline = 1 and acycnrlc = 1 this bit is used to determine whether reset level clamping is used. 0 = rlc disabled, 1 = rlc enabled. 5:4 intm[1:0] 00 colour selection bits used in internal modes. 00 = red, 01 = green, 10 = blue and 11 = reserved. see table 4 for details. setup register 4 7:6 fm[1:0] 00 colour selection bits used in input force mux modes. 00 = rinp, 01 = ginp, 10 = binp and 11 = reserved. see table 4 for details. 0 vsmpdet 0 0 = normal operation, signal on vsmp input pin is applied directly to timing control block. 1 = programmable vsmp detect circuit is enabled. an internal synchronisation pulse is generated from signal applied to vsmp input pin and is applied to timing control block. 3:1 vdel[2:0] 000 when vsmpdet = 0 these bits have no effect. when vsmpdet = 1 these bits set a programmable delay from the detected edge of the signal applied to the vsmp pin. the internally generated pulse is delayed by vdel mclk periods from the detected edge. see figure 19, internal vsmp pulses generated for details. 4 posnneg 0 when vsmpdet = 0 this bit has no effect. when vsmpdet = 1 this bit controls whether positive or negative edges are detected: 0 = negative edge on vsmp pin is detected and used to generate internal timing pulse. 1 = positive edge on vsmp pin is detected and used to generate internal timing pulse. see figure 19 for further details. setup register 5 7:5 reserved 000 must be set to zero 3:0 seldis[3:0] 0000 selective power disable register - activated when selpd = 1. each bit disables respective cell when 1, enabled when 0. seldis[0] = red cds, pga seldis[1] = green cds, pga seldis[2] = blue cds, pga seldis[3] = adc setup register 6 7:4 reserved 0000 must be set to zero wm8196 production data w pd rev 4.3 march 2007 29 register bit no bit name(s) default description offset dac (red) 7:0 dac[7:0] 10000000 red channel offset dac value. offset dac (green) 7:0 dac[7:0] 10000000 green channel offset dac value offset dac (blue) 7:0 dac[7:0] 10000000 blue channel offset dac value offset dac (rgb) 7:0 dac[7:0] 10000000 a write to this register location causes the red, green and blue offset dac registers to be overwritten by the new value pga gain (red) 7:0 pga[7:0] 00000000 determines the gain of the red channel pga according to the equation: red channel pga gain = 208/(283-pga[7:0]) pga gain (green) 7:0 pga[7:0] 00000000 determines the gain of the green channel pga according to the equation: green channel pga gain = 208/(283-pga[7:0]) pga gain (blue) 7:0 pga[7:0] 00000000 determines the gain of the blue channel pga according to the equation: blue channel pga gain = 208/(283-pga[7:0]) pga gain (rgb) 7:0 pga[7:0] 00000000 a write to this register location causes the red, green and blue pga gain registers to be overwritten by the new value table 7 register control bits wm8196 production data w pd rev 4.3 march 2007 30 applications information recommended external components 3 10 1 28 27 7 5 6 12 11 9 4 dvdd1 dvdd2 agnd1 rinp ginp binp mclk vsmp rlc/acyc sck sen sdi oeb 8 26 24 25 23 20 19 18 17 16 15 14 13 op[0] op[1] op[2] op[3] op[4] op[5] op[6] op[7]/sdo vrlc/vbias vrx vrt vrb avdd c2 c1 c6 c8 c4 c5 c7 c9 avdd video inputs timing signals interface controls output data bus dgnd agnd agnd agnd 22 dgnd 21 c3 agnd agnd2 2 c11 c10 c12 avdd ++ + dgnd agnd wm8196 c1-9 should be fitted as close to wm8196 as possible. notes: agnd and dgnd should be connected as close to wm8196 as possible. 1. 2. dvdd1 dvdd2 dvdd1 dvdd2 figure 26 external components diagram recommended external component value component reference suggested value description c1 100nf de-coupling for dvdd1. c2 100nf de-coupling for dvdd2. c3 100nf de-coupling for avdd. c4 10nf high frequency de-coupling between vrt and vrb. c5 1 f low frequency de-coupling between vrt and vrb (non-polarised). c6 100nf de-coupling for vrb. c7 100nf de-coupling for vrx. c8 100nf de-coupling for vrt. c9 100nf de-coupling for vrlc. c10 10 f reservoir capacitor for dvdd1. c11 10 f reservoir capacitor for dvdd2. c12 10 f reservoir capacitor for avdd. table 8 external components descriptions wm8196 production data w pd rev 4.3 march 2007 31 package dimensions notes: a. all linear dimensions are in millimeters. b. this drawing is subject to change without notice. c. body dimensions do not include mold flash or protrusion, not to exceed 0.20mm. d. meets jedec.95 mo-150, variation = ah. refer to this specification for further details. dm007.e ds: 28 pin ssop (10.2 x 5.3 x 1.75 mm) symbols dimensions (mm) min nom max a ----- ----- 2.0 a 1 0.05 ----- 0.25 a 2 1.65 1.75 1.85 b 0.22 0.30 0.38 c 0.09 ----- 0.25 d 9.90 10.20 10.50 e e 7.40 7.80 8.20 5.00 5.30 5.60 l 0.55 0.75 0.95 a a2 a1 14 1 15 28 e1 e c l gauge plane 0.25 e b d seating plane -c- 0.10 c ref: jedec.95, mo-150 e 1 l 1 1.25 ref 0.65 bsc l 1 0 o 4 o 8 o wm8196 production data w pd rev 4.3 march 2007 32 important notice wolfson microelectronics plc (?wolfson?) products and services are sold subject to wolfson?s terms and conditions of sale, delivery and payment supplied at the time of order acknowledgement. wolfson warrants performance of its products to the specifications in effect at the date of shipment. wolfson reserves the right to make changes to its products and specifications or to discontinue any product or service without notice. customers should therefore obtain the latest version of relevant information from wolfson to verify that the information is current. testing and other quality control techniques are utilised to the extent wolfson deems necessary to support its warranty. specific testing of all parameters of each device is not necessarily performed unless required by law or regulation. in order to minimise risks associated with customer applications, the customer must use adequate design and operating safeguards to minimise inherent or procedural hazards. wolfson is not liable for applications assistance or customer product design. the customer is solely responsible for its selection and use of wolfson products. wolfson is not liable for such selection or use nor for use of any circuitry other than circuitry entirely embodied in a wolfson product. wolfson?s products are not intended for use in life support systems, appliances, nuclear systems or systems where malfunction can reasonably be expected to result in personal injury, death or severe property or environmental damage. any use of products by the customer for such purposes is at the customer?s own risk. wolfson does not grant any licence (express or implied) under any patent right, copyright, mask work right or other intellectual property right of wolfson covering or relating to any combination, machine, or process in which its products or services might be or are used. any provision or publication of any third party?s products or services does not constitute wolfson?s approval, licence, warranty or endorsement thereof. any third party trade marks contained in this document belong to the respective third party owner. reproduction of information from wolfson datasheets is permissible only if reproduction is without alteration and is accompanied by all associated copyright, proprietary and other notices (including this notice) and conditions. wolfson is not liable for any unauthorised alteration of such information or for any reliance placed thereon. any representations made, warranties given, and/or liabilities accepted by any person which differ from those contained in this datasheet or in wolfson?s standard terms and conditions of sale, delivery and payment are made, given and/or accepted at that person?s own risk. wolfson is not liable for any such representations, warranties or liabilities or for any reliance placed thereon by any person. address: wolfson microelectronics plc westfield house 26 westfield road edinburgh eh11 2qb united kingdom tel :: +44 (0)131 272 7000 fax :: +44 (0)131 272 7001 email :: sales@wolfsonmicro.com |
Price & Availability of WM8196SCDSR
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |